Professor Motor is very pleased to bring you the best available drag racing products. Listed below are the products currently in our catalog. Larger color illustrations can be found by clicking the link associated with the part number. Thank you for your interest in drag racing cars & parts by Professor Motor. Check out the Motor Catalog for motors to use for drag racing and the 1/24 Catalog or 1/32 Catalog for other parts.
Please check stock status in our online shopping if you would like to determine if an item is immediately available.
Part Number |
PICTURE |
Price / Card |
PRODUCT |
P582 |
$18.59 |
Parma Edge Drag Chassis - 1/24 Scale Inline Chassis for C Can or D can motors. Uses P626 square "adjusta-bushings"To ORDER please click here to use online shopping. |
|
P626 |
$1.70 |
Parma square "adjusta-bushings" for drag chassis - use with 1/8" drill blank axlesTo ORDER please click here to use online shopping. |
|
PMTR1081 |
$19.95 |
Professor Motor Chassis Kit - Vintage Style Brass Rod Side Rails - Includes robust stamped motor bracket for Fox / Cheetah / Falcon style motors, brass drop arm, 1/16" brass tube for body mounts (via pins), precut front & rear axle tubes, brass tube and rod for drop arm pivot. Makes this chassis or longer wheelbase similar chassis for 1/24 or 1/32 drag racing.To ORDER please click here to use online shopping. |
|
BW50010 |
$10.00 |
BWA Billet machined brass motor bracket for scratch building - mounts Cheetah / Falcon / Little Ripper / TSRF & 16D type motors. May be used for 1/32 or 1/24 scale chassis building. Bracket has 3/16" bore for axle bushings or ball bearings & 0.047" diameter holes for frame rails at the bottom of the motor mounting face.To ORDER please click here to use online shopping. |
|
PMTR5012 |
$5.95 |
Stamped brass motor bracket for scratch building - mounts Cheetah / Falcon / Little Ripper / TSRF type motors. Motor has 1/16" offset at top edge of bracket - allows for flush to bottom mount or raised motor position to allow for larger diameter tire use. Rear axle mounts 2 ways - use 7/32" brass tube with 3/16" bushings or open holes to 1/4" for 1/4" bushings or bearingsTo ORDER please click here to use online shopping. |
|
PMTR5013 |
$3.95 |
Stamped brass drop arm for scratch building - accepts 3/16" post guide flag - 3/4" wideTo ORDER please click here to use online shopping. |
|
PMTR1073 |
|
$1.49 |
Low friction style Oilite bushing - 3/32" ID x 3/16" OD flanged - 1 pair / packageTo ORDER please click here to use online shopping. |
PMTR1074 |
|
$1.25 |
Oilite bushing - 1/8" ID x 3/16" OD flanged - 1 pair / packageTo ORDER please click here to use online shopping. |
PMTR1021 |
|
$1.25 |
1 pair 1/8" x 1/4" flanged axle Oilite bushingsTo ORDER please click here to use online shopping. |
PMTR1016 |
|
$1.75 |
1/8" diameter Drill Blank axle - Heat Treated Tool Steel, 2 1/2" long, Centerless GroundTo ORDER please click here to use online shopping. |
PMTR1069 |
$1.99 |
High quality 3/32" diameter drill blank axle - 2 1/8" (54mm) long - heat treated & centerless ground tool steel - made in GermanyTo ORDER please click here to use online shopping. |
|
PMTR1017 |
|
$1.95 |
29 tooth Cox crown gear for 1/8" diameter axle - 48 pitch - includes setscrew - setscrew mount to plain or threaded axleTo ORDER please click here to use online shopping. |
PMTR1018 |
|
$1.95 |
35 tooth Cox crown gear for 1/8" diameter axle - 48 pitch - includes setscrew - setscrew mount to plain or threaded axleTo ORDER please click here to use online shopping. |
